How To Paint Satinwood Paint Over Gloss? DIY Guide

To produce a smooth, clean and consistent finish while painting satinwood paint over gloss, you need to have a fair amount of time and special treatment. The first step in any painting of satin paint on gloss paint you need to sand the surface to remove as much gloss paint as possible to allow the paint to adhere due to the slick surface.
To enable the paint to stick to the surface, you should apply at least two base coats of bonding primer. It would be best if you gave each coat enough time to dry before applying the following layer. Read the complete answer on What is satin paint?
How To Paint Satinwood Paint Over Gloss? DIY Guide
The following are the steps to applying satin paint over gloss undercoat:
Step 1:
It would be best if you cleared out the path by removing all the obstacles and hurdles into your working area to avoid any paint splash over the goods.
Step 2:
Cover all the mediums with any plastic sheeting or drop cloths to protect them from the paint that drops during your DIY job. The plastic sheeting or drop cloth will prevent you from making any mess while you work. This sheeting can be available from the nearby paint supply store, home improvement store, or online. Learn about How To Apply Satinwood Paint?
Step 3:
Flush the sheeting edges or drop clothes with painter’s tape to avoid any paint from escaping the covered area. You can even apply painter’s tape to any trim or other areas which can’t be reached by the sheeting or drop cloths for a reason mentioned earlier.
Step 4:
The flake and dust particles of paint can be dangerous and even fatal in some cases as they could irritate your lungs and throats. Make sure you wear a face mask to cover your face. You should also wear gloves and other safety gear to prevent the paint from splashing all over your hands or clothing while painting. The paint could be a laboring task to remove, particularly from your clothes.
Step 5:
As you know, the step to painting satin paint over gloss service would be to de-gloss the undercoat finish to make it less slippery and allow the paint to adhere to it properly. You can de-gloss the surface by sanding the paint finish in circular motions using 180-grit sandpaper. You need to sand the finish enough to make it less glossy. There is no need to remove all the paint as it could be very time-consuming.
Step 6:
Sand all the surfaces, including corners or crevices, so that you are free of any glossy sheen. You should only utilize 180 to 220-grit sandpaper as the coarser sandpaper with a higher grit can damage and strip your surface of the undercoat paint. Find out the best Satinwood Paints
Step 7:
Pour about a liter of lukewarm water into a container. Add a teaspoon of dish soap and a quarter of a teaspoon of vinegar in it. Combine the content by stirring the mixture well. The lukewarm water ensures that soapy studs are formed, which helps to eliminate any dirt, dust, or grime. Let the mixture rest for at least ten minutes on very stubborn stains before wiping it off with a sponge. Don’t scrub the stain too forcefully, as it can damage the paint.
Step 8:
Dip the sponge into the mixture prepared for cleaning and remove the excess water from the sponge by wringing it to make it almost dry. A cellulose sponge without a scrubbing side would serve the purpose. Use as little water as possible to avoid any streaks or oversaturation of the gloss paint.
Step 9:
After you have cleaned the paint’s surface with the clean sponge, you should move on to the drying process. To dry the surface of the paint of any moisture, you should use a dry and clean towel or cloth. You should avoid drying the paint forcefully as it might trap the fabrics of the paint on your surface, and you could also chip or damage the paint.
All these can affect the final look of the new paint you have to apply on top of the base coat. Let the surface completely dry to touch by pressing your finger slightly after leaving the surface to dry for an hour.
Step 10:
To prevent any flaking or chipping of the paint from the surface of the undercoat, you should cover it with a layer of primer. A thin layer of primer on the surface of the gloss paint would suffice. The top of the surface would be your starting point, and you should move down to cover the area evenly. The primer could be applied by using a paintbrush or roller to cover it with broad strokes. Read our review on Best Paint for Trim.
Step 11:
The primer you have applied would have the drying time mentioned on its packaging. Let the primer dry till the required time without disturbing it. Lightly press your finger to see if the paint has dried. If your finger comes back clean, then you are good to go. A fan or exhaust would allow the airflow to improve and enable the primer to dry quickly.
Step 12:
After the primer coat has been dried, you can finally paint your desired paint coat color on the prepared surface. This paint can be applied using a paintbrush, paint roller, or paint sprayer. To get an even coat of paint, you should start from the top and work your way down. Since your surface has been sanded and prepared, you can apply any paint on your gloss paint. These could include oil-based, water-based latex, acrylic, or any other kind of paint. Find out Best Paint for Wood Crafts.
Step 13:
Let the paint dry before applying a second coat to get the proper paint coverage and color and avoid any gloss paint or primer visibility.

Benjamin Drake, also known as Ben, is an enthusiastic painter who has been working with the paints and wood industry since 2005. After collaborating with leading paint industries, he is now on the path to guide locals about the knowledge he had attained throughout these years so that our dedicated users always make the right decision.